10/100/1000BASE Copper SFP Transceiver

Features

1.Up to at least one 1.25Gb/s bi-directional data links

2.Hot-pluggable SFP footprint

3.Extended case temperature range :0°C to 70°C(Standard), -40°C to 85°C (Industrial)

4.Fully metallic enclosure for low EMI

5.Low power dissipation (1.05 W typical)

6.Compact RJ-45 connector assembly

7.Usage of physical layer IC via 2-wire serial bus

8.1000 BASE-T procedure in host systems with SERDES interface

9.10/100/1000Mbps compliant in host systems with SGMII interface

Applications

1.25 Gigabit Ethernet over Cat 5 cable

Description

OEMfibers Copper Small Type Pluggable (SFP)transceivers is powerful, affordable module compliant with the Gigabit Ethernet and 1000BASE-T Transceiver standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supp- orting 1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The module supports1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All pairs in the cable are used in combination with symbol rate at 250Mbps on each pair. The module provides standard serial ID information compliant with SFP MSA, which may be accessed with address of A0h via the 2wire serial CMOS EEPROM protocol. The physical IC may also be accessed via 2wire serial bus at address ACh.

评论

发表评论

此博客中的热门博文

Differences between cisco GLC-T and cisco GLC-TE

 Cisco GLC-T, GLC-TE and SFP-GE-T optical modules are all Gigabit port optical modules with RJ45 interface and 100m transmission distance. They are cost-saving solutions for Gigabit Ethernet connection in data center, access network and storage area network applications. Therefore, these three types of optical modules are often difficult to distinguish. In fact, the transmission effect of these three optical modules is the same, which optical module can achieve Gigabit transmission, but it is certainly noteworthy that the original Cisco GLC-T and SPF-GE-T optical modules were terminated on June 1, 2017 and replaced by GLC-TE optical module. SFP-GE-T optical module with NEBS 3 ESD function needs to be selected if it is traded directly with the telecommunications company (which requires NEBS).The price of GLC-T and GLC-TE optical modules is low, and they can also meet the needs of Gigabit Ethernet. The Cisco Gigabit optical modules provided by Easy Communications can meet a large number
阅读全文

Cisco 10GBASE SFP+ Modules Data Sheet

 Product overview The Cisco 10GBASE SFP+ modules offer you a wide variety of 10 Gigabit Ethernet connectivity options for data center, enterprise wiring closet, and service provider transport applications. Features and benefits Cisco SFP+ modules offer the following features and benefits. Industry’s smallest 10G form factor for greatest density per chassis Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Supports “pay-as-you-populate” model for investment protection and ease of technology migration Digital optical monitoring capability for strong diagnostic capabilities Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the same link Cisco quality Identification (ID) feature enables a Cisco platform to identify whether the module is certified and tested by Cisco Cisco SFP-10G-SR-S module (S-Class) The Cisco 10GBASE-SR module supports a link length of 26 meter
阅读全文

Why the sfp transceiver not work

 The failure of the sfp optical module is divided into the failure of the transmitter and the failure of the receiver. Through the analysis of the main causes of the phenomenon, the most likely problems are mainly concentrated in the following aspects: The optical port of the  1000base SFP transceiver  is contaminated and damaged Because of the pollution and damage of the optical interface of the module, the loss of the optical link is increased, so that the optical fiber link is unreachable. The main reasons for this phenomenon are the following four points: 1. The optical port of the SFP optical module has been exposed to the environment for a long time, resulting in contamination and contamination of the SFP optical port; 2. The end face of the fiber jumper connected to the  Cisco SFP-10g-sr  optical module has been contaminated, and the SFP optical port provides been contaminated; 3. Improper operation of the end face of the optical connector with pigtails, scratching of the finish
阅读全文