The CFP2 optical transceiver installation process

OEMfibers shares the installation process of the CFP2 optical transceiver. What preparations and precautions should be taken before installation?

First, preparation before installation To prevent the static electricity generated during the installation of the CFP2 optical transceiver or the electronic elements in the device, before installing or removing the CFP2 optical transceiver, put an antistatic wrist strap on the wrist, tighten the lock, and confirm the antistatic wrist. Bring good contact with the skin and make sure the ESD wrist strap is normally well grounded.

Second, the installation and disassembly of CFP2 optical transceiver

Warning: Do not touch the gold finger area of the CFP2 optical transceiver directly by hand during the procedure for installing or removing the 100G CFP2 modules .

1 Turn the metal handle up vertically

2 As proven in the figure, ensure that the transceiver is installed in the correct direction (the handle is located above the fiber interface), and push the transceiver into the slot in the horizontal direction until you hear the sound of the transceiver jamming the slot. The transceiver is in close connection with the slot. Continue to push the transceiver hard

1 Pull out the fiber linked to the Brocade 100G-CFP2-LR4-10KM and pull the metal handle down to the horizontal position.

2 Pull the handle and pull the transceiver out in the horizontal direction. When pulling out, apply also force to avoid damage to the handle.

Third, matters needing attention

1 If an optical fiber is inserted in to the CFP2 optical transceiver to be installed or removed, remove the fiber and install or take away the CFP2 transceiver.

2 When inserting a CFP2 optical transceiver, first check whether the transceiver is correctly inserted into the port, and make sure that the direction is correct and there is no misalignment, offset, etc., and then push the transceiver into place.

3 When removing the CFP2 optical transceiver , pull out the plug in a horizontal direction. If the force direction is at an angle to the horizontal direction, the plug may end up being difficult to pull out or even damage the transceiver and the slot.
After the 4CFP2 optical transceiver is installed, if the fiber is not installed immediately, insert the protective rubber plug of the transceiver in to the optical port on the transceiver.

评论

发表评论

此博客中的热门博文

Differences between cisco GLC-T and cisco GLC-TE

 Cisco GLC-T, GLC-TE and SFP-GE-T optical modules are all Gigabit port optical modules with RJ45 interface and 100m transmission distance. They are cost-saving solutions for Gigabit Ethernet connection in data center, access network and storage area network applications. Therefore, these three types of optical modules are often difficult to distinguish. In fact, the transmission effect of these three optical modules is the same, which optical module can achieve Gigabit transmission, but it is certainly noteworthy that the original Cisco GLC-T and SPF-GE-T optical modules were terminated on June 1, 2017 and replaced by GLC-TE optical module. SFP-GE-T optical module with NEBS 3 ESD function needs to be selected if it is traded directly with the telecommunications company (which requires NEBS).The price of GLC-T and GLC-TE optical modules is low, and they can also meet the needs of Gigabit Ethernet. The Cisco Gigabit optical modules provided by Easy Communications can meet a large number
阅读全文

Cisco 10GBASE SFP+ Modules Data Sheet

 Product overview The Cisco 10GBASE SFP+ modules offer you a wide variety of 10 Gigabit Ethernet connectivity options for data center, enterprise wiring closet, and service provider transport applications. Features and benefits Cisco SFP+ modules offer the following features and benefits. Industry’s smallest 10G form factor for greatest density per chassis Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Supports “pay-as-you-populate” model for investment protection and ease of technology migration Digital optical monitoring capability for strong diagnostic capabilities Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the same link Cisco quality Identification (ID) feature enables a Cisco platform to identify whether the module is certified and tested by Cisco Cisco SFP-10G-SR-S module (S-Class) The Cisco 10GBASE-SR module supports a link length of 26 meter
阅读全文

Why the sfp transceiver not work

 The failure of the sfp optical module is divided into the failure of the transmitter and the failure of the receiver. Through the analysis of the main causes of the phenomenon, the most likely problems are mainly concentrated in the following aspects: The optical port of the  1000base SFP transceiver  is contaminated and damaged Because of the pollution and damage of the optical interface of the module, the loss of the optical link is increased, so that the optical fiber link is unreachable. The main reasons for this phenomenon are the following four points: 1. The optical port of the SFP optical module has been exposed to the environment for a long time, resulting in contamination and contamination of the SFP optical port; 2. The end face of the fiber jumper connected to the  Cisco SFP-10g-sr  optical module has been contaminated, and the SFP optical port provides been contaminated; 3. Improper operation of the end face of the optical connector with pigtails, scratching of the finish
阅读全文