OEMfibers SFP fiber transceiver features

1 SFP port + 1 RJ45 electrical port 10 / 100M adaptive Ethernet fiber optic transceiver Fiber optic transceiver can be used anywhere in the network, combining new technologies and existing products to support new applications, technologies and future development. No need for expensive comprehensive upgrades, fiber optic transceivers can extend the life cycle of existing cables and active equipment. OEMfibers provides 10 / 100Base Ethernet optical fiber transceiver, 1000Base Gigabit optical fiber transceiver, SFP transceiver , optional single- mode dual-core fiber, multimode dual-core fiber and single-mode single-core fiber. We also provide fiber optic transceiver racks, such as 14-slot fiber optic transceiver racks and 16-slot fiber optic transceiver racks for managing various fiber optic transceivers.

Features: Automatic crossover & pass-through: Automatic monitoring, configure the twisted pair port on the transceiver to achieve the correct MDI or MDI-X configuration Link transmission: Link transmission is a fault diagnosis function, which allows the optical fiber transceiver to monitor the optical Automatic link recovery of signal loss of the port and RX electrical port: Under all network conditions, the optical fiber transceiver will automatically rebuild the link. The optional speed setting: the transceiver can be set to 10Mbps or 100Mbps. The optical and electrical ports are automatically set to the same rate.

Main features An RJ45 electrical port and an SFP port, it can convert the photoelectric Ethernet signal between 10 / 100M UTP port and 100M optical port, and the Ethernet signal between the exchange ports. Adaptive function supports UTP port to automatic 10 / 100M and full-duplex / half-duplex to prevent broadcast storm. Supports VLAN and QoS. Supports up to 1536 Bytes. Low power consumption (3W), low heat, good stability

The application extends the Ethernet network distance: by using the 10GBASE-T to 10BASE- FL rate setting (back-to-back) to extend the distance of any two 10BASE-T devices to 100KM. Use single-mode fiber without repeater to increase the length of Fast Ethernet network: Use single-mode fiber to extend the distance of any two 10BASE-TX devices to 100KM utilizing the settings of 100BASE-TX to 100BASE-FX Or directly connect to a 100BASE-FX compatible port on any device to provide a 100BASE-TX interface

评论

发表评论

此博客中的热门博文

Differences between cisco GLC-T and cisco GLC-TE

 Cisco GLC-T, GLC-TE and SFP-GE-T optical modules are all Gigabit port optical modules with RJ45 interface and 100m transmission distance. They are cost-saving solutions for Gigabit Ethernet connection in data center, access network and storage area network applications. Therefore, these three types of optical modules are often difficult to distinguish. In fact, the transmission effect of these three optical modules is the same, which optical module can achieve Gigabit transmission, but it is certainly noteworthy that the original Cisco GLC-T and SPF-GE-T optical modules were terminated on June 1, 2017 and replaced by GLC-TE optical module. SFP-GE-T optical module with NEBS 3 ESD function needs to be selected if it is traded directly with the telecommunications company (which requires NEBS).The price of GLC-T and GLC-TE optical modules is low, and they can also meet the needs of Gigabit Ethernet. The Cisco Gigabit optical modules provided by Easy Communications can meet a large number
阅读全文

Cisco 10GBASE SFP+ Modules Data Sheet

 Product overview The Cisco 10GBASE SFP+ modules offer you a wide variety of 10 Gigabit Ethernet connectivity options for data center, enterprise wiring closet, and service provider transport applications. Features and benefits Cisco SFP+ modules offer the following features and benefits. Industry’s smallest 10G form factor for greatest density per chassis Hot-swappable input/output device that plugs into an Ethernet SFP+ port of a Cisco switch (no need to power down if installing or replacing) Supports “pay-as-you-populate” model for investment protection and ease of technology migration Digital optical monitoring capability for strong diagnostic capabilities Optical interoperability with 10GBASE XENPAK, 10GBASE X2, and 10GBASE XFP interfaces on the same link Cisco quality Identification (ID) feature enables a Cisco platform to identify whether the module is certified and tested by Cisco Cisco SFP-10G-SR-S module (S-Class) The Cisco 10GBASE-SR module supports a link length of 26 meter
阅读全文

Why the sfp transceiver not work

 The failure of the sfp optical module is divided into the failure of the transmitter and the failure of the receiver. Through the analysis of the main causes of the phenomenon, the most likely problems are mainly concentrated in the following aspects: The optical port of the  1000base SFP transceiver  is contaminated and damaged Because of the pollution and damage of the optical interface of the module, the loss of the optical link is increased, so that the optical fiber link is unreachable. The main reasons for this phenomenon are the following four points: 1. The optical port of the SFP optical module has been exposed to the environment for a long time, resulting in contamination and contamination of the SFP optical port; 2. The end face of the fiber jumper connected to the  Cisco SFP-10g-sr  optical module has been contaminated, and the SFP optical port provides been contaminated; 3. Improper operation of the end face of the optical connector with pigtails, scratching of the finish
阅读全文